Chapter 10: Khuếch đại thuật toán

Chia sẻ: Dovan Thuc | Ngày: | Loại File: PPT | Số trang:45

Thêm vào BST

Báo xấu

158
lượt xem 35
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

Operation amplifier: Symbol, Example, Characteristics, Structure, Operation, Applications. Characters of circuits depend on outside circuit structure, not the opamp itself, Gain AV: very high, ideally ∞, Zin: very large, ideally ∞, Zout: very small, ideally 0.

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Chapter 10: Khuếch đại thuật toán

Operation amplifier  Symbol  Example  Characteristics  Structure  Operation  Applications  μp 741
Symbol
Example
Characteristics  Characters of circuits depend on outside circuit structure, not the opamp itself  Gain AV: very high, ideally ∞  Zin: very large, ideally ∞  Zout: very small, ideally 0  Current entering the amp at either terminal: extremely small, ideally 0  Voltage out (when voltages into each other are equal): small, ideally 0  Bandwidth: broad, ideally infinite
Characteristics  Input: 2 inputs (positive and negative)  Single-ended input: 1 input to signal source, 1 input to ground  Double-ended input: 2 different signal sources or 1 signal source apply between 2 inputs  Output: 1 or 2 outputs, typically 1 output  Mode gain:  Differential-mode gain Adm - large  Common-mode gain Acm - small  Common-mode rejection ratio CMRR=G=Adm/Acm, usually about 103-105
Structure  Requirement:  Gain: large  Offset: small  Currents: small  Input impedance: large  Output impedance: small  Input: symmetric
Structure  Input stage  Intermediate stage  Level shifting stage  Output stage  Example: 741 – at the end of chapter
Applications  Basic and advance applications  Basic applications:  Inverting, non-inverting amplifier  Uni-gain circuit  Addition and subtraction circuits  Integration and differential circuits  Multi-stages circuit
Applications  Advance applications  Current-controlled voltage source  Voltage-controlled current source  DC voltmeter  AC voltmeter  Driver circuit  Active filters  NIC  .etc.
Non-inverting fixed-gain amplifier Prove:  V- = V+ = V 1  I- = I+ = 0 =>IR1 = Irf = V1/R1 =>A = 1+Rf/R1
Non-inverting fixed-gain amplifier A = 1+Rf/R1=101 Vo=101Vi
Inverting fixed-gain amplifier Prove:  V- = V+ = 0  I- = I+ = 0 =>IR1 = Irf = V1/R1 =>A = -Rf/R1
Voltage addition Vo = -V1Rf/R1-V2Rf/R2 – V3Rf/R3 If V1=V2=V3 then: A= -Rf/R1-Rf/R2 –Rf/R3
Voltage subtraction Vout1 = -Rf/R1V1 Vout = -Rf/R2V2 - Rf/R2Vout1 = -Rf/R2V2 + Rf/R2V1 = -Rf/R2(V1 – V2)
Voltage subtraction with 1 amp Prove:  V-=V+=V *R /(R +R ) 1 3 1 3  I- = I+ = 0 =>IR1 = IR4 = V2- V1*R3/ (R1+R3) =>Vo=V1*R3/(R1+R3)* (R2+R4)/R2 – V2*R4/R2
Uni-gain (buffer) amplifier  Provide required input and output resistant stage  Provide multiple identical output signals
Voltage-controlled voltage source  Vo=(1+Rf/R1)V1  Vo=(-Rf/R1)V1
Voltage-controlled current source  Io=V1/R1
Current-controlled voltage source  Vo=-I1RL
Current-controlled current source  Io=I1(R2+R1)/R2