Thông tin thiết kế mạch P1

Chia sẻ: Tien Van Van | Ngày: | Loại File: PDF | Số trang:16

Thêm vào BST

Báo xấu

88
lượt xem 13
download

Download Vui lòng tải xuống để xem tài liệu đầy đủ

THE HISTORY OF TELECOMMUNICATIONS According to UNESCO statistics, in 1997, there were 2.4 billion radio receivers in nearly 200 countries. The ﬁgure for television was 1.4 billion receivers. During the same year, it was reported that there were 822 million main telephone lines in use world-wide. The number of host computers on the Internet was estimated to be 16.3 million [1]. In addition to this, the military in every country has its own communication network which is usually much more technically sophisticated than the civilian network. ...

Chủ đề:

Bình luận(0) Đăng nhập để gửi bình luận!

Lưu

Nội dung Text: Thông tin thiết kế mạch P1

Telecommunication Circuit Design, Second Edition. Patrick D. van der Puije Copyright # 2002 John Wiley & Sons, Inc. ISBNs: 0-471-41542-1 (Hardback); 0-471-22153-8 (Electronic) 1 THE HISTORY OF TELECOMMUNICATIONS 1.1 INTRODUCTION According to UNESCO statistics, in 1997, there were 2.4 billion radio receivers in nearly 200 countries. The ﬁgure for television was 1.4 billion receivers. During the same year, it was reported that there were 822 million main telephone lines in use world-wide. The number of host computers on the Internet was estimated to be 16.3 million [1]. In addition to this, the military in every country has its own commu- nication network which is usually much more technically sophisticated than the civilian network. These numbers look very impressive when one recalls that electrical telecommunication is barely 150 years old. One can well imagine the number of people employed in the design, manufacture, maintenance and operation of this vast telecommunication system. 1.2 TELECOMMUNICATION BEFORE THE ELECTRIC TELEGRAPH The need to send information from one geographic location to another with the minimum of delay has been a quest as old as human history. Galloping horses, carrier pigeons and other animals have been recruited to speed up the rate of information delivery. The world’s navies used semaphore for ship-to-ship as well as from ship-to-shore communication. This could be done only in clear daylight and over a distance of only a few kilometres. The preferred method for sending messages over land was the use of beacons: lighting a ﬁre on a hill, for example. The content of the message was severely restricted since the sender and receiver had to have previously agreed on the meaning of the signal. For example, the lighting of a beacon on a particular hill may inform one’s allies that the enemy was approaching from the north, say. In 1792, the French Legislative Assembly approved funding for the demonstration of a 35 km visual telegraphic system. This was essentially 1
2 THE HISTORY OF TELECOMMUNICATIONS semaphore on land. By 1794, Lille was connected to Paris by a visual telegraph [3]. In England, in 1795, messages were being transmitted over a visual telegraph between London and Plymouth – a return distance of 800 km in 3 minutes [4]. North American Indians are reputed to have communicated by creating puffs of smoke using a blanket held over a smoking ﬁre. Such a system would require clear daylight as well as the absence of wind, not to mention a number of highly skilled operators. A method of telecommunication used in the rain forests of Africa was the ‘‘talking drum’’. By beating on the drum, a skilled operator could send messages from one village to the next. This system of communication had the advantage of being operational in daylight and at night. However, it would be subject to operator error, especially when the message had to be relayed from village to village. 1.3 THE ELECTRIC TELEGRAPH The ﬁrst practical use of electricity for communication was in 1833 by two professors from the University of Goettingen, Carl Friedrich Gauss (1777–1855) and Wilhelm Weber (1804–1891). Their system connected the Physics Institute to the Astronomical Observatory, a distance of 1 km, and used an induction coil and a mirror galvanometer [4]. In 1837, Charles Wheatstone (1802–1875) (of Wheatstone Bridge fame) and William Cooke (1806–1879) patented a communication system which used ﬁve electrical circuits consisting of coils and magnetic needles which deﬂected to indicate a letter of the alphabet painted on a board [5]. The ﬁrst practical use of this system was along the railway track between Euston and Chalk Farm stations in London, a distance of 2.5 km. Several improvements were later made, the major one being the use of a coding scheme which reduced the system to a single coil and a single needle. The improvement of the performance, reliability and cost of commu- nication has since kept many generations of engineers busy. At about the time when Wheatstone and Cooke were working on their system, Samuel Morse (1791–1872) was busy doing experiments on similar ideas. His major contribution to the hardware was the relay, also called a repeater. By connecting a series of relays as shown in Figure 1.1, it was possible to increase the distance over Figure 1.1. The use of Morse’s relay to extend the range of the telegraph.
1.3 THE ELECTRIC TELEGRAPH 3 which the system could operate [5]. Morse also replaced the visual display of Wheatstone and Cooke with an audible signal which reduced the fatigue of the operators. However, he is better known for his efﬁcient coding scheme which is based on the frequency of occurrence of the letters in the English language so that the most frequently used letter has the shortest code (E: dot) and the least frequently used character has the longest code (‘–apostrophe: dot-dash-dash-dash-dash-dot). This code was in general use until the 1950s and it is still used by amateur radio operators today. In 1843, Morse persuaded the United States Congress to spend $30,000 to build a telegraph line between Washington and Baltimore. The success of this enterprise made it attractive to private investors, and Morse and his partner Alfred Vail (1807– 1859), were able to extend the line to Philadelphia and New York [6]. A number of companies were formed to provide telegraphic services in the east and mid-west of the United States. By 1851, most of these had joined together to form the Western Union Telegraph Company. By 1847, several improvements had been made to the Wheatstone invention by the partnership of Werner Siemens (1816–1892) and Johann Halske (1814–1890) in Berlin. This was the foundation of the Siemens telecommunication company in Germany. The next major advance came in 1855 when David Hughes (1831–1900) invented the printing telegraph, the ancestor of the modern teletype. This must have put a lot of telegraph operators out of work (a pattern which was to be repeated over and over again) since the machine could print messages much faster than a person could write. Another improvement which occurred at about this time was the simultaneous transmission of messages in two directions on the same circuit. Various schemes were used but the basic principle of all of them was the balanced bridge. In 1851, the ﬁrst marine telegraphic line between France and England was laid, followed in 1866 by the ﬁrst transatlantic cable. The laying of this cable was a major feat of engineering and a monument to perseverance. A total of 3200 km of cable was made and stored on an old wooden British warship, the HMS Agamemnon. The laying of the cable started in Valentia Bay in western Ireland but in 2000 fathoms of water, the cable broke and the project had to be abandoned for that year. A second attempt the following year was also a failure. A third attempt in 1858 involved two ships and started in mid-ocean and it was a success. Telegraphic messages could then be sent across the Atlantic. The celebration of success lasted less than a month when the cable insulation broke down under excessively high voltage. Interest in transatlantic cables was temporarily suspended while the American Civil War was fought and it was not until 1865 that the next attempt was made. This time a new ship, the Great Eastern, started from Ireland but after 1900 km the cable broke. Several attempts were made to lift the cable from the ocean bed but the cable kept breaking off so the project was abandoned until the following year. At last in 1866, the Great Eastern succeeded in laying a sound cable and messages could once more traverse the Atlantic. By 1880, there were nine cables crossing the ocean [6]. The telegraph was and remained a communication system for business, and in most European countries it became a government monopoly. Even in its modernized
4 THE HISTORY OF TELECOMMUNICATIONS form (telex) it is essentially a cheap long-distance communication network for business. 1.4 THE FACSIMILE MACHINE In 1843, the British Patent Ofﬁce issued a patent with the title ‘‘Automatic electrochemical recording telegraph’’ to the Scottish inventor Alexander Bain (1810–1877). The essence of the invention is shown in Figure 1.2. Two identical pendulums are connected as shown by the telegraph line. For simplicity, we assume the ‘‘message’’ to be sent is the letter H and it is engraved on a metallic plate and shaped to the appropriate radius so that the ‘‘read’’ stylus makes contact with the raised parts of the plate as the pendulum sweeps across it. On the far end of the telegraph line, the stylus of the second pendulum maintains contact with the electrosensitive paper which rests on an electrode shaped to the same radius as before. The electrosensitive paper has been treated with a chemical which produces a dark spot when electric current ﬂows through it. To operate the system, both pendulums are released from their extreme left positions simultaneously. Since they are identical, it follows that they will travel at the same speed, one across the ‘‘message’’ plate and the other across the electro- sensitive paper. At ﬁrst no current ﬂows, but as the transmitter pendulum makes contact with the raised portion of the plate, the circuit is complete and the resulting current causes the electrosensitive paper to produce a dark line of the same length as the raised metal segment. The original patent included the functions: (a) an electromagnetic device to keep the pendulums swinging at a constant amplitude Figure 1.2. The conﬁguration of the Bain ‘‘Automatic electrochemical recording telegraph.’’ To keep the diagram simple, additional circuits required for synchronization, phasing and scanning are not shown.
1.4 THE FACSIMILE MACHINE 5 (synchronization), (b) a second electromagnetic arrangement to ensure that the two pendulums start their swings at the same instant (phasing), and (c) a mechanism to move the message plate and the electrosensitive paper simultaneously one step at a time after each sweep at right angles to the direction of the pendulum swing (scanning). When several sweeps have occurred, the lines produced will form an exact image of the raised metal parts of the ‘‘message’’ plate. Figure 1.3(a) shows the letter H scanned in 20 lines and Figure 1.3(b) shows the corresponding current waveforms. Figure 1.3(c) shows the reproduced image. All the facsimile machines since the Bain patent have the three functions listed above. In modern facsimile machines, the ﬁrst two functions have been replaced by electronic techniques which ensures that the transmitter and the receiver are ‘‘locked’’ to each other at all times. The mechanism for scanning the message is also largely electronic, although in most machines it is still necessary to move the page mechanically as it is scanned. In 1848, Frederick Bakewell, an Englishman, produced a new version of the fax machine in which the ‘‘message plate’’ as well as the image were mounted on Figure 1.3. (a) Shows the letter H scanned in 20 lines, (b) shows the current waveforms for each line scanned and (c) shows the reproduced H. Note the effect of the ﬁnite width of the receiver stylus on the image.
6 THE HISTORY OF TELECOMMUNICATIONS cylinders which were turned by falling weights, similar to a grandfather clock. To ensure that the cylinders turned at the same speed he used a mechanical speed governor. The scanning head (stylus) was propelled on an axis parallel to that of the cylinder by a lead-screw. This was an example of ‘‘spiral scanning’’. Unlike Bain, he used an insulating ink to write the message on a metallic surface. But, as before, the paper in the receiver was chemically treated to respond to the ﬂow of electric current and it was mounted on an identical cylinder with the ‘‘write’’ head driven by an identical lead-screw. The main difﬁculty with this design was the necessity to keep the two clock motors in remote locations starting and running at the same speed during the transmission. In 1865, Giovanni Caselli (1815–1891), an Italian living in France, patented an improved version of Bain’s machine which he called the ‘‘Pantelegraph’’. He then established connections between Paris and a number of other French cities. His machine was a combination of the insulating ink message plate of Bakewell, the pendulum of Bain’s transmitter, and the Bakewell cylindrical receiver. The pantele- graph was a commercial success and it was used in Italy and Britain for many years. By the end of the 1800s it was possible to send photographs by fax. The picture had to be etched on a metallic plate in the form of raised dots (similar to the technique used for printing pictures in newspapers). The size of the dots represented the different shades of gray; small for light and large for dark gray. The transmitter stylus traced lines across the picture making contact with the raised dots and thus producing corresponding large and small dots at the receiver. In 1902, Arthur Korn demonstrated a scanning system which used light instead of physical contact with a metallic plate and the resultant ﬂow of current. His method was far superior to all the previous techniques, especially in the transmission of photographs. He wrapped the photographic ﬁlm negative of the picture on the outside of a glass cylinder which was turned at a constant rate by an electric motor. An electric lamp provided the light and a system of lenses were used to focus the light onto the negative. The light that passed through the ﬁlm was reﬂected by a mirror onto a piece of selenium whose resistance varied according to how much light reached it. The selenium cell was used to control the current ﬂowing in the receiver. The receiver recorded the image directly onto ﬁlm. To ensure that the transmitter and receiver cylinders were in synchronism at all times, he used a central control system with a tuning fork generating the control signal. In the 1920s the large American telecommunication companies, American Telephone and Telegraph (AT&T), Radio Corporation of America (RCA) and Western Union, became interested in fax machine development and they used new techniques, materials and devices such as the vacuum tube, phototubes and later semiconductors to produce the modern fax machine. 1.5 THE TELEPHONE In 1876, Alexander Graham Bell (1847–1922) was conducting experiments on a ‘‘harmonic telegraph’’ system when he discovered that he could vary the electric
1.5 THE TELEPHONE 7 current ﬂowing in a circuit by vibrating a magnetic reed held in close proximity to an electromagnet which formed part of the loop. By connecting a second electromagnet together with its own magnetic reed in the circuit, he could reproduce the vibration of the ﬁrst reed. Using a human voice to excite the magnetic reed led to the ﬁrst telephone for which he was granted a patent later that year. He went on to demonstrate his invention at the International Centennial Exhibition in Philadelphia and before the year ended, he transmitted messages between Boston, Massachusetts, and North Conway, New Hampshire, a distance of 230 kilometres. Few people realized the potential of the new invention and in 1878, when Bell tried to sell his patent to the Western Union Telegraph Company, he was turned down [7]. The early telephone system consisted of two of Bell’s magnetic reed-electro- magnet instruments in series with a battery and a bell. Bell’s instrument worked very well as a receiver, in fact so well that it has survived almost unchanged to this day. As a transmitter, however, it left a lot to be desired. It was soon replaced by the carbon microphone (one of the many inventions of Thomas Edison (1847–1931)) which was, until recently, the most widely used microphone in the telephone system. In the early telephone system, each subscriber was connected to a central ofﬁce by a single wire with an earth return. This led to cross-talk between subscribers. At about this time, electric traction had become very popular which resulted in increased interference from the noise generated by the electric motors. The earth- return system was gradually replaced by two-wire circuits which are much less susceptible to cross-talk and electrical noise. The rapid growth of the telephone system was based almost entirely on the fact that the subscriber could use the system with the minimal amount of training. The ease of operation of the telephone outweighed the disadvantages of having no written record of conversations and the requirement that both parties have to be available for the call at the same time. The basic central ofﬁce responds to a signal from the subscriber (calling party) indicating that he wants service. A buzzer excited by current from a hand-cranked magneto was the standard. The telephone operator answers and ﬁnds out whom (called party) the calling party wants to talk to. The operator then signals to the called party by connecting his own hand-cranked magneto to the line and cranking it to ring a bell on the called party’s premises. When and if the called party responds, he connects the lines of the two parties together and withdraws until the conversation is over, at which point he disconnects the lines. In order to carry out his function, the operator had to have access to all the lines connected to the exchange. This was not a problem in an exchange with less than ﬁfty lines but as the system grew, more operators were required for each group of ﬁfty subscribers. If the calling party and called party belong to the same group of ﬁfty, the above sequence was followed. If they belong to two different operators, it was necessary for the two operators to have a verbal consultation before the connection could be made. The errors, delays and misunderstandings in large central ofﬁces led to a re-organization whereby each operator responded to only ﬁfty incoming lines but had access to all the outgoing lines. Another improvement in the system was to replace all the batteries on the subscribers’ premises with one battery in the central ofﬁce.
8 THE HISTORY OF TELECOMMUNICATIONS The motivation for the changeover from manual switching to the automatic telephone exchange was not, as one would expect, the inability of the central ofﬁce to cope with the increasing volume of trafﬁc. It was because the operators could listen to the conversations. The inventor of the automatic exchange, Almon B. Strowger (1839–1902), after whom the system was named, was an undertaker in Kansas City around the 1890s. There was another undertaker in the city whose wife worked in the local telephone exchange; whenever someone died in the city, the telephone operators were the ﬁrst to know and the wife would pass a message to the husband, giving him a head-start on his competitor [8]. The automatic exchange certainly improved the security of telephone conversations; it was also one more example of machines replacing people. The success of the telephone system led to a large number of small telephone companies being formed to service the local urban communities. Pressure to inter- connect the various urban centres soon grew and techniques for transmission over longer distances had to be developed. These included ampliﬁcation and inductive loading. Since these transmission lines (trunks) were expensive to construct and maintain, techniques for transmission of more than one message (multiplex) over the trunk at any one time became a matter of great concern and an area of rapid advancement. 1.6 RADIO In 1864, James Maxwell (1831–1879), a Scottish physicist, produced his theory of the electromagnetic ﬁeld which predicted that electromagnetic waves can propagate in free space at a velocity equal to that of light [9]. Experimental conﬁrmation of this theory had to wait until 1887 when Heinrich Hertz (1857–1894) constructed the ﬁrst high-frequency oscillator. When a voltage was induced in an induction coil connected across a spark gap, a discharge would occur across the gap setting up a damped sinusoidal high-frequency oscillation. The frequency of the oscillation could be changed by varying the capacitance of the gap by connecting metal plates to it. The detector that he used consisted of a second coil connected to a much shorter spark gap. The observation of sparks across the detector gap when the induction coil was excited showed that the electromagnetic energy from the ﬁrst coil was reaching the second coil through space. These experiments were in many ways similar to those carried out in 1839 by Joseph Henry (1797–1878). Several scientists made valuable contributions to the subject, such as Edouard Branly (1844–1940) who invented the ‘‘coherer’’ for wave detection, Aleksandr Popov (1859–1906) and Oliver Lodge (1851–1940) who discovered the phenomenon of resonance. In 1896, Guglielmo Marconi (1874–1937) left Italy for England where he worked in cooperation with the British Post Ofﬁce on ‘‘wireless telegraph’’. A year later, he registered his ‘‘Wireless Telegraphy and Signal Co. Ltd’’ in London, England to exploit the new technology of radio. On the 12th of December 1901, Marconi received the letter ‘‘S’’ in Morse code at St, Johns, Newfoundland on his receiver whose antenna was held up by a kite, the antenna which he had constructed for the
1.7 TELEVISION 9 purpose having been destroyed by heavy winds. He had confounded the many skeptics who thought that the curvature of the earth would make radio transmission impossible [10]. Up to this point, no use had been made of ‘‘electronics’’ in telecommunication: high-frequency signals for radio were generated mechanically. The ﬁrst electronic device, the diode, was invented by Sir John Ambrose Fleming (1849–1945) in 1904. He was investigating the ‘‘Edison effect’’ that is, the accumulation of dark deposits on the inside wall of the glass envelope of the electric light bulb. This phenomenon was evidently undesirable because it reduced the brightness of the lamp. He was convinced that the dark patches were formed by charge particles of carbon given off by the hot carbon ﬁlament. He inserted a probe into the bulb because he had the idea that he could prevent the charged particles from accumulating by applying a voltage to the probe. He soon realized that, when the probe was held at a positive potential with respect to the ﬁlament, there was a current in the probe but when it had a negative potential no current would ﬂow: he had invented the diode. He was granted the ﬁrst patent in electronics for his effort. Fleming went on to use his diode in the detection of radio signals – a practice which has survived to this day. The next major contribution to the development of radio was made by Lee DeForest (1873–1961). He got into legal trouble with Marconi, the owner of the Fleming diode patent, when he obtained a patent of his own on a device very similar to Fleming’s. He went on to introduce a piece of platinum formed into a zig-zag around the ﬁlament and soon realised that, by applying a voltage to what he called the ‘‘grid’’, he could control the current ﬂowing through the diode. This was, of course, the triode – a vital element in the development of ampliﬁers and oscillators. 1.7 TELEVISION Shortly after the establishment of the telegraph, the transmission of images by electrical means was attempted by Giovanni Caselli (1815–1891) in France. His technique was to break up the picture into little pieces and send a coded signal for each piece over a telegraph line. The picture was then reconstituted at the receiving end. The system was slow, even for static images, but it established the basic principles for image transmission; that is, the break up of the picture into some elemental form (scanning), the quantization of each element in terms of how bright it is (coding), and the need for some kind of synchronization between the transmitter and the receiver. Subsequent practical image transmission schemes, whether mechanical or electronic, had these basic units. The discovery in 1873 by Joseph May, a telegraph operator at the Irish end of the transatlantic cable, that when a selenium resistor was exposed to sunlight its resistance decreased, led to the development of a light-to-current transducer. Subsequently, various schemes for image transmission based on this discovery were devised by George Carey, William Ayrton (1847–1908), John Perry and others. None of these was successful because they lacked an adequate scanning system and
10 THE HISTORY OF TELECOMMUNICATIONS each element of the picture had to be sent on a separate circuit, making them quite impractical. In 1884, Paul Nipkow (1860–1940) was granted a patent in Germany for what became known as the Nipkow Disc. This consisted of a series of holes drilled in the form of spirals in a disc. When an image is viewed through a second disc with similar holes driven in synchronism with the ﬁrst, the observed effect was scanning point-to-point to form a complete line and line-by-line to cover the complete picture. This was a practical scheme since the point-to-point brightness of the picture could be transmitted and received serially on a single circuit. The persistence of an image on the human eye could be relied on to create the impression of a complete scene when, in fact, the information is presented point-by-point. Nipkow’s scheme could not be exploited until 1927 when photosensitive cells, photomultipliers, electron tube ampliﬁers and the cathode ray tube had been invented and had attained sufﬁcient maturity to process the signals at an acceptable speed for television. Several people made signiﬁcant contributions to the development of the components as well as to the system. However, two people, Charles Jenkins (1867–1934) and John Baird (1888–1946), are credited with the successful transmission of images at about the same time. They both used the Nipkow disc. Mechanical scanning methods of various forms were used with reasonable success until about 1930 when Vladimir Zworykin (1889–1982) invented the ‘‘iconoscope’’ and Philo Farns- worth (1906–1971) the electronic camera tube, which he called the ‘‘image dissector’’. These inventions ﬁnally removed all the moving parts from television scanning systems and replaced them with electronic scanning [11]. The application of very-high-frequency carriers and the use of coaxial cables have contributed signiﬁcantly to the quality of the pictures. The use of color in television had been shown to be feasible in 1930 but would not be available to the general public until the mid-1960s. By the 1980s, satellite communication systems brought a large number of television programs to viewers who could afford the cost of the dish antenna. By the beginning of the 21st century, the dish antennas had shrunk in size from over 3 m to less than 70 cm and the signal had changed into digital form. 1.8 THE GROWTH OF BANDWIDTH AND THE DIGITAL REVOLUTION Electrical telecommunication started with a single wire with a ground return, but, as the system grew, the common ground return had to be replaced with a return wire, hence the advent of the open-wire telephone line. The open-wire system with its forests of telegraph poles along city streets strung with an endless array of wires eventually gave way to the twisted pair cable. The twisted pair cable owes its existence to improved insulating materials, mainly plastics, which reduced the space requirements of the cable. The bandwidth of an unloaded twisted pair is approxi- mately 4 kHz and it decreases rapidly with length. This can be improved by connecting inductors (loading coils) in series with the line at speciﬁc distances and by various equalization schemes to about 1 MHz. However, the twisted pair has found a niche in the modern telephone system where its bandwidth approximately
1.9 THE INTERNET 11 matches that required for analog audio communication. This is still the dominant mode of telephone communication up to the central ofﬁce. Beyond the central ofﬁce the network of inter-ofﬁce trunks use a variety of conduits for the transmission of the signal. Increased bandwidth alone was not an answer to the expanding telecommunica- tion trafﬁc. High-frequency carriers had to be developed in order to exploit fully the bandwidth capability of new telecommunication media such as coaxial cables, terrestrial microwave networks and ﬁber optics. The development of the coaxial cable, which conﬁnes the electromagnetic wave to the annular space between the two concentric conductors, reduced signiﬁcantly the radiation losses that would other- wise occur. As a result the bandwidth was increased to approximately 1 GHz and attenuation was reduced. Terrestrial as well as satellite microwave communication systems have further expanded the bandwidth into the terrahertz range and, for those who can afford the dish antenna and its associated equipment, it has increased the number of television channels available to over 800. The application of ﬁber optics to telecommunication has extended the channel bandwidth to that of visible light (1 Â 1012 Hz). It is now possible for one optical ﬁber to carry as many as 300 Â 109 telephone channels at the same time. An increasingly dominant factor in telecommunication is the enormous popular- ity of digital techniques. The information is reduced to a train of pulses (binary digits; 1s and 0s) and sent over the channel. The limited bandwidth, phase change and the noise in the channel cause the signal to deteriorate so it is necessary to ‘‘refresh’’ or regenerate the signal at various points along the channel. This is accomplished by using repeaters whose function is to determine whether the digit sent was a 1 or a 0 and to generate the appropriate new digits and transmit them. At the receiving end, the digits are converted back into an analog signal. The compact disc music recording system is a common example of this technique. Although the need for information transfer between computers spurred on the development of digital communication, speech signals increasingly are being converted into digital form for telephone transmission. 1.9 THE INTERNET The use of personal computers as a means of communication gained enormous popularity in the last decade of the 20th century. However, computer science experts have used the ARPANET (Advanced Research Projects Agency of the U.S. Department of Defense) for communication between computers since 1969. The basic idea was to enable scientists in different geographic locations to share their research results [12] and also, as a money saving scheme, their computing resources. The ﬁrst four sites to be connected were the Stanford Research Institute, the University of California at Los Angeles, the University of California at Santa Barbara, and the University of Utah in Salt Lake City. The messages traveling between these centers were over 50 kbps telephone lines. In 1962 when the ARPANET was being designed, the Cold War was in full swing and so one of the
12 THE HISTORY OF TELECOMMUNICATIONS speciﬁcations for the design was that the network should survive a nuclear attack in which parts of it were knocked out [13]. Needless to say, this feature of the design was never tested! The ideal structure was a network with every node connected to every other node (high redundancy) so that, if a part of the network went down for whatever reason, the trafﬁc could be routed around the trouble spot. Moreover, in such a design all nodes are of equal importance, hence there is no one node the destruction of which would cripple the network. The conﬁguration of the network is shown in Figure 1.4. This is similar to the electric power grid which was designed to provide electric power to consumers with a maximum reliability service. Another design feature of the ARPANET which further improved its robust nature was the use of ‘‘packet’’ switching. In packet switching, the incoming message is ﬁrst divided into smaller packets of binary code. Each packet is labeled with a number and the address of its destination and then transmitted to the next node when the local router can accommodate the packet. Each packet, in theory, can travel from the source to the destination by a different route and arrive at different times. At its destination the packets are re-assembled in the proper order ready for the recipient. The strength of packet switching is the fact that, if a number of nodes are put out of operation, the packets will still ﬁnd their way to their proper destination by way of the remaining operational nodes, in perhaps a longer time. Moreover, error- detection codes can be included with each packet and, when errors are present in a packet, that packet can be re-sent. The ARPANET grew so that by 1983 there were 562 sites connected. By 1992, the number of ‘‘host’’ or ‘‘gateway’’ computers connected to it had reached one million. Four years later, the number was 12 million. It has been estimated that by the year 2000 the number with access to the Internet worldwide will be 100 million [14]. The term ‘‘Internet’’ came into use in 1984, and this was also the time when the Figure 1.4. Each node of the Internet is connected to all the neighboring nodes. The increased redundancy implies a high level of reliability. The design of the electric power grid follows the same principle for the same reason.
1.10 THE WORLD WIDE WEB 13 United States Department of Defense handed over the oversight of the network to the National Science Foundation. The Internet is currently run in a very loose fashion by a number of volunteer organizations whose membership is open to the public. Their main activity is centered around the registration of names, numbers and addresses of the users of the system. The Internet is a collection of a large number of computers connected together by telephone lines, coaxial cables, optical ﬁber cables and communication satellites with set protocols to enable communication between them and also to control the ﬂow of trafﬁc. 1.10 THE WORLD WIDE WEB What factors have contributed to the unprecedented growth of the Internet? Personal computers have been in common use in scientiﬁc laboratories and in universities since the mid-1980s but they were mostly used for calculation, information storage and retrieval. Many businesses acquired desk-top computers for preparing invoices, word-processing and general book-keeping. Some enthu- siasts owned their own personal computers and some belonged to clubs for the exchange of computer software which they had developed. The growth of computing power of the personal computer was one of the pivotal developments that made the Internet possible. In 1971, the Intel Corporation produced its ﬁrst microprocessor, the Intel 4004. It was used in a calculator and its clock frequency (an indication of how fast it operates) was 108 kHz. The following year the Corporation produced the Intel 8008 which was twice as fast (200 kHz) as the 4004 and it was used in 1974 in a predecessor of the ﬁrst personal computer. Also in 1974, Intel produced the 8080 which was clocked at 2 MHz. The 8080 was marketed to computer enthusiasts as part of a kit and it very quickly became the ‘‘brains’’ of the modern personal computer. By the year 2000, the Intel Pentium III processor had achieved a clocking speed of 1.13 GHz (over four orders of magnitude faster than the original 4004). This phenomenal increase in speed was coupled to an equally incredible decrease in price which made the personal computer affordable to the general public. A hypothetical comparison with the automobile industry in 1983 was as follows: ‘‘If the automobile business had developed like the computer business, a Rolls-Royce would now cost $2.75 and run 3 million miles on a gallon of gas’’ [15]. Even this comparison was considered conservative ﬁfteen years later. In the Spirit of the Web, Wade Rowland amends the statement as follows: ‘‘That Rolls-Royce would now cost twenty-seven cents and run 300 million miles on a gallon of gas’’. The telephone system was already in place, although its capacity would have to be expanded to carry the digital data in addition to the voice signals for which it was designed. Most of the main communication lines carrying Internet data have been
14 THE HISTORY OF TELECOMMUNICATIONS updated, for example the copper cables (coaxial) laid across continents and on the sea-bed are capable of 2.5 Mbps and ﬁber optic cables can go as high as 40 Gbps. The building of the throughways for large volumes of data was the easy part of the problem. The more difﬁcult part was to get the data to its destination in the workplaces and into the living quarters of the owners of personal computers. Unfortunately, the cost of wiring houses with optical ﬁber cable or even coaxial cable cannot be justiﬁed on economic grounds. Currently, the speed limit to data ﬂow is determined by the analog telephone line (sometimes referred to as a ‘‘twisted pair’’) between the central ofﬁce (or its equivalent) and the wall socket to which the most personal computers are connected. This is popularly known as the-last-mile problem. New circuits have been developed to speed up data transfer on the existing twisted pair cable. These include the T1, the Integrated Services Digital Network (ISDN), the High-bit-rate Digital Subscriber Line (HSDL) and the Asymmetrical Digital Subscriber Line (ASDL). In the early 1990s, cable television service had reached into a large number of homes in North America and Europe and there was talk of them providing high- bandwidth (mainly coaxial cable) conduits to subscribers for access to the Internet. Unfortunately, the television cable network had millions of ampliﬁers and one-way traps installed which restricted signal ﬂow in only one direction. Connection to the Internet required a bilateral ﬂow of information and the cost of the conversion was considered prohibitive. At the time this book was going to press, the cable television companies were in the process of converting their networks for bilateral ﬂow of information (cable modems). The speed of transmission was predicted to be from 10 Mbps to 400 Mbps [16]. Another serious impediment to the free ﬂow of data from one computer to another was the almost incomprehensible commands required to effect computer commu- nication. The ‘‘spoken language’’ of the computers was UNIX and this was quite unfriendly to the uninitiated. The ‘‘point-and-click’’ feature of the computer ‘‘mouse’’ and the development of browsers, such as Netscape Navigator and the Internet Explorer, ﬁnally lowered the threshold to a level where even computer neophytes could successfully access information from the Internet. These ‘‘facil- itators’’ were all available by 1989 and they would have a very profound effect on the popularity of the Internet. The Internet can be seen as a network connecting various sites where information is stored. The stored information and the technology for transferring the information back and forth is the World Wide Web. The World Wide Web in its infancy carried only text. Later the transmission of graphics, in color, was added. With the increasing speed and sophistication of the personal computer, sound and video have been added subsequently. What made the Web particularly useful is the ability of the Internet browsers and search engines to provide a list of Internet sites where the requested information may be located. It is necessary to prompt the system with a set of keywords for the search to begin. At the Web site there are ‘‘links’’ to other sites so the search can ‘‘fan out’’ in very many directions. An important factor that stimulated the growth of the Internet was the decision of the United States government to turn over the running of the Internet to commercial
REFERENCES 15 interests. This happened in stages. The National Science Foundation’s NSFnet was superceded by the Advanced Networks and Services network, ANSnet, a non-proﬁt organization. However, in 1998 the Federal Communications Commission (FCC) insisted that subscribers to the telephone system be billed at the same rate for voice services as for data. The way was now open for commercial organizations to offer their services on the Internet. The Internet Service Providers (ISP) collect money from their subscribers for access to their servers. They in turn have to pay for access to the long-distance, high-speed Internet backbone. The decentralized nature of the Web and its ability to transfer information bilaterally meant that its users could add their own contribution to the vast amount already present in the form of their ‘‘personal home page’’. Commercial organizations, special-interest groups and even governments would take advantage of the possibilities offered by the Web. But so would people and groups with hidden and not-so-hidden agendas to propagate their own distortions. As there is no authority to monitor the content of the Web sites, only the criminal laws of the country in which the Web site is registered can be used to control information on the sites. A number of services are available to people who have access to the Internet. Newsgroups can be found on practically any topic. These newsgroups run round- the-clock and anyone can join in the discussion from his or her keyboard. The participants are free to use assumed names and identities. The number of people in any given newsgroup can vary from zero to several thousand, so it is possible to reach a very large audience from one’s keyboard. Chat rooms are similar to newsgroups except that the number of people ‘‘in’’ a chat room is likely to be much smaller. It is essentially a conversational mode of communication from one’s keyboard. One of the more popular features of the Internet is electronic mail (e-mail). It is the nearest thing to mailing a letter to a correspondent, and although it is not as secure as the service provided by the Post Ofﬁce, it is much faster. To send e-mail, one has to register a unique e-mail address and choose a password. REFERENCES 1. Statistical Yearbook 1999, UNESCO, Paris. 2. Berto, C., Telegraphes et Telephones de Valmy au Microprocesseurs, Le Livre de Poche, 1981. 3. Stumpers, F. L. H. M., ‘‘The History, Development and Future of Telecommunications in Europe’’, IEEE Comm. Magazine, 22(5), 1984. 4. Fraser, W., Telecommunications, MacDonald & Co, London, 1957. 5. Tebo, Julian D., ‘‘The Early History of Telecommunications’’, IEEE Comm. Soc. Digest, 14(4), pp. 12–21, 1976. 6. Osborne, H. S., Alexander Graham Bell, Biographical Memoirs, Nat. Acad. Sci., Vol. 23, pp 1–29, 1945.
16 THE HISTORY OF TELECOMMUNICATIONS 7. Smith, S. F., Telephony and Telegraphy A, 2nd Ed., Oxford University Press, New York, 1974. 8. Bernal, J.D., Science in History, Vol. 2, Penguin Books Ltd, Middlesex, 1965. 9. Carassa, F., ‘‘On the 80th Anniversary of the First Transatlantic Radio Signal’’, IEEE Antennas Propagat. Newsl., pp. 11–19, Dec., 1982. 10. Knapp, J. G. and Tebo, J. D., ‘‘The History of Television’’, IEEE Comm. Soc. Digest, 16(3), pp 8–21, May 1978. 11. Licklider, J. C. R. and Clark, W., ‘‘On-line Man-Computer Communications’’, Massachu- setts Institute of Technology, Aug., 1962. 12. Baran, P., ‘‘On Distributed Communications Networks’’, RAND Corporation, Washington DC, Sept., 1962. 13. Zakon, R. H., ‘‘Hobbes’ Internet Timeline v5.1’’ at www.isoc.org/zakon/internet, Oct., 2000. 14. ‘‘The Computer Moves In’’, Time, January 3, 1983, 10. 15. Rowland, W., Spirit of the Web, Somerville House Pub., Toronto, 1997. 16. www.wired.com/news BIBLIOGRAPHY Jones, C. R., Facsimile, Murray Hill Books, New York, 1949. Costigan, D. M., Fax: The Principles and Practice of Facsimile Communication, Chilton Book Co., Philadelphia, 1971. McConnell, K., Bodson, D., and Urban, S., Fax: Facsimile Technology and Systems, 3rd Ed., Artech House, Boston, 1999. Dodd, Annabel, Z. The Essential Guide to Telecommunications, 2nd Ed., Prentice-Hall, Englewood Cliffs, NJ, 2000. Lehnert, Wendy, G., Internet 101: A Beginner’s Guide to the Internet and the World Wide Web, Addison-Wesley, Reading, MA, 1998.