Microstructure and mechanical properties
-
A gas metal arc welding robot was used to build a thin-walled component made of mild steel on a low-carbon substrate according to the AM principle. Thereafter, the specimens for observing microstructures and mechanical properties were extracted from the built thin-walled component. The microstructures of the specimen were observed by an optical microscope; the hardness was measured by a digital microhardness tester, and the tensile tests were carried out on a tensile test machine.
8p larachdumlanat127 02-01-2021 11 2 Download
-
The additional network-modifying cation oxide breaking up this network by the generation of nonbridging O atoms and it has a slight effect on the topology of SiOx and OSiy units. Moreover, the diffusion of network- former atom in sodium-silicate melt is anomaly and diffusion coefficient for sodium atom is much larger than for oxygen or silicon atom. The simulation proves two diffusion mechanisms of the network-former atoms and modifier atoms.
10p tamynhan6 14-09-2020 15 4 Download
-
In this paper, a feasibility study concerning the generation of tensile specimens using a quenching dilatometer is presented. The ODS steel investigated contains 9%Cr and exhibits a phase transformation between ferrite and austenite around 870 °C.
8p christabelhuynh 30-05-2020 32 2 Download
-
This study focuses on 316L stainless steel fabricated by selective laser melting (SLM) in the context of nuclear application, and compares with a cold-rolled solution annealed 316L sample. The effect of heat treatment (HT) and hot isostatic pressing (HIP) on the microstructure and mechanical properties is discussed.
10p christabelhuynh 29-05-2020 14 2 Download
-
In this paper, the severe plastic deformation method (SPD) known as constrained groove pressing (CGP) was applied to produce ultrafine-grained microstructure in IF steel sheets. In the CGP technique, samples are subjected to repetitive shear deformation under the plane strain deformation condition using the constrained grooved and flat dies.
6p tohitohi 19-05-2020 8 1 Download
-
Aluminium alloy AlMg4.5Mn has got comprehensive acceptance in the manufacturing of light weight frames, marine structures which require high strength and worthy corrosion revulsion. The present investigation work focuses on friction stir welding process in which influences of operating parameters have been studied on friction stir welded butt joints.
10p tohitohi 19-05-2020 36 2 Download
-
In this summary, we briefly review the recent studies focused on the structure and mechanical behavior of HEAs, covering the important issues from phase stability to elastic modulus, mechanical strength, hardness and fatigue resistance. Finally, we highlight a few key findings recently reported for HEAs and discuss the outstanding issues yet to be resolved.
20p tohitohi 19-05-2020 9 1 Download
-
In this paper, butt joining of Al5083 to commercially pure copper is investigated by friction stir welding method. The effects of transverse welding speed of the tool on the mechanical properties and microstructure of the joint were studied, experimentally.
8p tohitohi 19-05-2020 12 2 Download
-
A dynamic nanoindentation method was applied to study an Fe-18 at.% Gd alloy as a neutron-absorbing material prepared by vacuum arc-melting and cast in a mold. The Fe-18 at.% Gd cast alloy had a microstructure with matrix phases and an Fe-rich primary dendrite of Fe9Gd. Rietveld refinement of the X-ray spectra showed that the Fe-18 at.% Gd cast alloy consisted of 35.84 at.% Fe3Gd, 6.58 at.% Fe5Gd, 16.22 at.% Fe9Gd, 1.87 at.% Fe2Gd, and 39.49 at.% b-Fe17Gd2. The average nanohardness of the primary dendrite phase and the matrix phases were 8.7 GPa and 9.3 GPa, respectively.
5p minhxaminhyeu4 26-06-2019 16 1 Download
-
Is a branch of polymer science dealing with analysis and characterisation of polymers. üThe complication of macromolecular chains, the dispersion in molecular weight, tacticity, crystallinity, orientation, composition of polymers etc. and complex morphological systems ⇒ analysis of polymer ≠ the small organic materials ⇒ Focus on viscoelastic properties, dynamic mechanical testing.
114p buitiendung87 06-01-2011 338 154 Download